10R - Helmet Install

Option A: Using the Hook and Loop Fasteners for Main Unit

1. Clean the area on the left side of the helmet where you will attach the hook and loop fasteners for main unit with a moistened towel and dry thoroughly.
2. Peel off the cover of the adhesive tape of the loop fastener for main unit and attach it to the helmet.

3. Peel off the cover of the adhesive tape of the hook fastener for main unit and attach it to the back plate of the main unit.

4. Attach the main unit using the hook and loop fasteners that you fitted. Make sure that the main unit is firmly attached to the helmet.

 

Option B: Using the Double Sided Adhesive Tapes for Main Unit

If you cannot attach the hook and loop fasteners to the helmet, you can use double sided adhesive tape.

1. Clean the area on the left side of the helmet where you will attach the double sided adhesive tapes with moistened towel and dry thoroughly.

2. Peel off the cover from one side of the double sided adhesive tapes for main unit and attach it to the back plate of the main unit.

3. Peel off the cover from the other side of the double sided adhesive
tapes and attach the main unit on the left side of your helmet.

4. Make sure that the main unit sticks on the helmet firmly. Maximum adhesion occurs after 24 hours.

CAUTION:
Sena recommends using the hook and loop fasteners for main unit. The
double sided adhesive tape is provided for convenience, but is not the
recommended mounting method. Sena is not responsible for its use.

 

Installing the Speakers

1. Peel off each cover of the hook and loop fasteners for speakers to expose the adhesive surface. Then, attach the fasteners to the ear pockets inside the helmet.

2. Attach the speakers to the hook and loop fasteners for speakers inside the helmet.

3. Align the arrows on the main unit and speaker cables and insert speaker cables into each speaker connector.

Note:
1. Three cables connect to the main unit. The longest is the cable for the
speakers. The second longest cable has a male connector and is for the
battery pack. The shortest cable is for the microphone.
2. The cable for the speakers has two leads. The longer lead is for the right
speaker and the shorter lead is for the left speaker.
3. If the helmet has deep ear pockets, you can use the speaker pads to
bring the speakers closer to your ears.

 

Installing the Microphones - Wired Boom

1. Peel off the cover of the hook and loop fastener for wired boom microphone to expose the adhesive tape. Then, attach the hook and loop fastener on the inside surface of the left external shell.

2. Attach the wired boom microphone’s mounting plate to the hook and loop fastener.

Note:
1. After you install the wired boom microphone, make sure you reinstall the
helmet’s internal padding.
2. You can use the boom microphone holder after attaching the hook and
loop fastener for boom microphone holder on it to ensure secure
installation.

3. Make sure that the microphone’s receiver is located near your mouth.

4. Adjust the head of the microphone so that the tab is facing away from your mouth.

5. Align the arrows on the main unit and microphone cables and insert the microphone cable into the microphone connector

Note:
Three cables connect to the main unit. The longest is the cable for the
speakers. The second longest cable has a male connector and is for the
battery pack. The shortest cable is for the microphone.

 

Using the Wired Microphone

If you have a full face helmet, you can use the wired microphone.

1. Peel off the cover of the hook and loop fastener for wired microphone to expose the adhesive tape. Then, attach the hook and loop fastener on the inside of the helmet’s chin guard.

2. Attach the wired microphone to the hook and loop fastener for wired microphone.

3. Align the arrows on the main unit and microphone cables and insert the microphone cable into the microphone connector.

Note:
Three cables connect to the main unit. The longest is the cable for the
speakers. The second longest cable has a male connector and is for the
battery pack. The shortest cable is for the microphone.

 

Installing the Battery Pack

1. Clean the area on the back side of the helmet where you will attach the double sided adhesive tapes with moistened towel and dry thoroughly.

2. Peel off the cover from one side of the double sided adhesive tapes for battery pack holder and attach it to the back plate of the battery pack holder.

3. Peel off the cover from the other side of the double sided adhesive tapes and attach the battery pack holder on the back side of your helmet.

4. Make sure that the double sided adhesive tapes sticks on the helmet firmly. Maximum adhesion occurs after 24 hours.

5. To secure the battery pack, slide the battery pack into the battery pack holder until you hear it click.

6. Align the arrows on the main unit and battery pack cables and insert the battery pack cable into the battery pack connector.

Note:
1. Three cables connect to the main unit. The longest is the cable for the
speakers. The second longest cable has a male connector and is for the
battery pack. The shortest cable is for the microphone.
2. To remove the battery pack from the battery pack holder, slide the battery
pack upward.
3. After connecting all the cables, store any excess cable behind the
internal padding of the helmet to prevent wires from becoming damaged.

Have more questions? Submit a request

0 Comments

Article is closed for comments.